BACK

#condenser coil cleaning

Tech Tips:

The photo above is of a real condenser coil we cleaned. The outer fins looked OK, but dirt and lint were packed deep inside. We also had sky-high head pressure and condensing temperature; those are telltale signs of an impacted condenser. That situation illustrates that a coil can sometimes look OK at first glance but […]

Washing Commercial Coils and Water Challenges – Short #292

In this short podcast episode, Bryan talks about considerations for washing commercial coils and water challenges techs might face. Despite being the topic of debate within the last several years, cleaning coils matters and will affect performance. When washing coils, we use Refrigeration Technologies Viper cleaners (especially Venom Packs) when we actually need cleaners. No […]

lma199927
#coil cleaning #condenser coil cleaning

Check out our most recent video

How to Evacuate an AC system, Full Vacuum Procedure

Our latest Podcast

HVAC School – For Techs, By Techs

Real training for HVAC ( Heating, Ventilation, Air Conditioning and Refrigeration) Technicians. Including recorded tech training, interviews, diagnostics and general conversations about the trade.

In this episode, Bryan sits down with compressor teardown specialist Ty Branaman for a deep dive into what really kills refrigeration and AC compressors. After some lighthearted banter, the conversation quickly turns technical: Ty has spent years cutting apart failed compressors on video, and he explains why that practice matters so much. As he puts it, he is “all about making the invisible visible” — once a technician actually sees what happened inside a dead compressor, vague explanations like “it just got old” stop holding up.

Bryan and Ty establish that a properly maintained compressor should essentially last forever, since it is a sealed system with no external contaminants — unlike an engine. The catch is that installation and service mistakes introduce the very contaminants that shorten its life. Copper plating tops Ty’s list of the most common findings: moisture combines with POE oil to form acid, which etches copper that then plates onto moving parts, thickening them and eventually causing hard starts that get mistaken for a “tired” compressor. They also trace how a shorted or seized compressor is usually the end result of an earlier root cause, not the cause itself.

The two work through the major categories of contamination one by one: solid debris from unswept lines and copper shavings left behind during deburring; moisture, which requires a proper pressure test, deep vacuum, and decay test to remove, plus heat to actually drive water molecules out; and non-condensable gases like oxygen and nitrogen, which throw off pressure readings and, with flammable A2L refrigerants, introduce real fire risk. Ty shares a memorable story about a compressor shell that ripped open after being left pressurized with nitrogen, and both discuss the surprisingly common problem of “wet” nitrogen and poorly maintained recovery tanks.

The conversation closes on flooded starts — a hazard Ty considers hugely overlooked — where migrated liquid refrigerant mixes with crankcase oil and violently flashes to vapor on startup, often shattering scroll plates. They cover practical prevention methods, including crankcase heaters, pump-down solenoids placed ahead of the metering device, and reduced refrigerant charges, before wrapping up with Ty’s quick field technique for cutting the top off a failed compressor to get an on-the-spot diagnosis rather than waiting on a full teardown back at the shop.

Topics Covered

Why compressors fail from external contamination rather than simply “wearing out”
Copper plating as the most frequently found problem inside failed compressors
Solid contaminants: dirt, copper shavings, and proper deburring technique
Moisture control: pressure testing, deep vacuum, decay testing, and heat-assisted evacuation
Wet nitrogen and poorly maintained recovery tanks
Oxygen and nitrogen contamination, including flammability risks with A2L refrigerants
Flooded starts, crankcase heaters, and pump-down solenoids
Superheat measured at the compressor versus at the evaporator outlet
Ty’s quick-cut technique for on-the-spot compressor diagnosis in the field

Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool.

Purchase your tickets or learn more about the 8th Annual HVACR Training Symposium at https://hvacrschool.com/symposium.

Subscribe to our podcast on your iPhone or Android.

Subscribe to our YouTube channel.

Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android.

Search Episodes

Compressor Failures, What and Why w/ Ty

07/09/2026

Bryan Orr

Multi Position Valves and More – Short #293

07/07/2026

Bryan Orr