BACK

HVAC Troubleshooting 101 w/ Jim Fultz

Make & share a podcast clip

Keep the exact passage and a link to the full episode. Choose up to three minutes, with enough context to be fair to the speaker.

Preview uses this episode’s audio. Browser audio export, when supported, takes the length of the selected clip. Nothing plays until you choose Preview.

In this session from the 2026 HVACR Training Symposium, Jim Fultz walks through his HVAC 101 class to help techs get through any gas furnace call. Jim’s core message is to start with your senses, not your meter. Look, listen, smell, and ask the homeowner what they experienced before touching a tool, then use instruments to confirm what your observations suggest.

An 80% furnace has a short list of components and a clear sequence of operations: call for heat, limit and pressure switch checks, inducer start, igniter warm-up, gas valve opening, flame proving, and the timed blower. When a furnace stops partway through that sequence, the stopping point tells you where to look. Jim also encourages techs to cycle a repaired furnace two or three times so they memorize what normal looks like, the way a bank teller learns real currency to spot counterfeits.

From there, Jim goes component by component, mixing practical tests with field stories. Topics include hot surface igniters, PSC and constant torque blower motors, capacitors, flame sensing, gas valves, pressure switches, and thermostat wiring. Along the way, he shares lessons such as checking amp draw even after a capacitor swap, measuring DC as well as AC on modern blower signals, and never assuming a wire’s color is consistent from end to end. He also explains why wiring works as pairs, which makes board replacement far easier.

Jim closes with a look at truck stock and time management, pointing out that every parts run costs a billable hour. He also covers some White-Rodgers resources, including the mobile cross-reference app, universal controls, and private-label thermostats.

Topics Covered

  • Developing a troubleshooting thought process: observe first, measure second
  • Using the board LED, thermostat batteries, and float switches as quick first checks
  • Recreating the homeowner’s complaint and listening to what customers report
  • Sequence of operation for an 80% furnace, including typical timings (15-second pre-purge, 17-second warm-up for 120V igniters, 5-second flame proving)
  • High-voltage versus low-voltage circuits, and why almost every component is wired in pairs
  • Tracing circuits on wiring diagrams one circuit at a time
  • Voltage versus continuity versus amperage: when to use each
  • Tracking down blown low-voltage fuses, from DIY thermostat installs to rubbed wires
  • Hot surface igniters: silicon carbide versus silicon nitride, cracks, and handling
  • PSC blowers, capacitor tolerances, and checking amp draw after a replacement
  • Constant torque (ECM X13) motors and the shift to DC control signals
  • Flame rectification: how it works, microamp readings, and cleaning the flame rod without sandpaper
  • Grounding problems, including a furnace that quit after a panel upgrade
  • Gas valves: DC coils, why you can’t ohm them, and checking inlet gas first
  • Pressure switch testing tips and thermostat wire continuity checks
  • Truck stock strategy, universal controls, and the cost of parts runs

 

The key takeaway from this session is to pay attention to where the actual sequence of operations differs from the expected sequence.

This episode contains embedded sponsor messages from Refrigeration Technologies, Carrier, Copeland, Santa Fe Dehumidifiers, and TruTech Tools.

Resources

 

Purchase your tickets or learn more about the 8th Annual HVACR Training Symposium at https://hvacrschool.com/symposium.

Work through this with the trade.

Highlight a short passage, or bring a question about a specific moment into HVAC No Bull Forum.

Discuss this reference → Related forum discussions

Comments

Why Every HVAC Company Needs a Home Performance Contractor – Short #312
Deliver High Performance Heat Pump Retrofits w/ David Richardson
Did You Actually Test Every Heat Strip – Short #311
Uncovering the Root Causes of Commercial Refrigeration Failures
Why and How to Test Heat Pump Defrost – Short #310
Building a Business That Lasts: Why Culture Beats Strategy in HVACR w/ Tony Gonzalez
Tight Enough to Fail – Short #309
Glycol Skids for Market Refrigeration w/ Max Johnson
Your Thermostat Is Reading the Wall – Short #308
Next-Gen Filtration – Pressure Drop, MERV 16, and Bypass Prevention w/ Chris Howells

Author:

To continue you need to agree to our terms.

The HVAC School site, podcast, and tech tips are
made possible by generous support from