BACK

#brownout

Tech Tips:

Brownouts and How They’re Killing HVAC Equipment

HVAC technicians typically focus on diagnosing issues related to mechanical wear, refrigerant leaks, or control problems within the equipment. However, damage can also originate from external sources. For instance, a failed control board might be attributed to internal shorts or rubouts. Yet, the root cause could be external, such as the voltage spike that can […]

Voltage Protection Devices

As HVAC technicians, our responsibilities extend beyond the mechanical and refrigerant systems. The electrical power supply is an often-overlooked factor in equipment longevity. Protecting an HVAC system from damaging voltage fluctuations is a strategic step that reduces service calls and enhances the reliability of our installations. This guide will discuss the importance of voltage protection […]

Check out our most recent video

How to Evacuate an AC system, Full Vacuum Procedure

Our latest Podcast

HVAC School – For Techs, By Techs

Real training for HVAC ( Heating, Ventilation, Air Conditioning and Refrigeration) Technicians. Including recorded tech training, interviews, diagnostics and general conversations about the trade.

In this essential episode, Bryan Orr sits down with Elliot, the residential install supervisor at Kalos Services, to unpack a critical issue that’s causing confusion among HVAC technicians, electricians, and inspectors alike: the new standards for breaker and conductor sizing on inverter-driven equipment. The conversation was sparked by Elliot’s frustrating experience of having two inspectors in the same county fail the same installation for opposite reasons—one for an oversized breaker and another for an undersized breaker. This contradiction led to a deep dive into recent changes in UL standards and how they affect everyday HVAC installations.

The heart of the issue stems from the transition to low-GWP refrigerants and the updated UL 60335-2-40 Edition 3 standard, which replaced the 1995 certification approach. This new standard introduced more conservative calculations for electrical characteristics, particularly affecting equipment using A2L refrigerants. The result? Data tags now show higher Minimum Circuit Ampacity (MCA) ratings than before, even though the equipment itself hasn’t changed—only the math used to calculate these values has shifted. This has created a puzzling situation where the MCA can be higher than the recommended breaker size, which seems counterintuitive to anyone familiar with traditional electrical principles.

Bryan and Elliot clarify the fundamental rule that still applies: size your wire to the MCA and your breaker to the MOCP (Maximum Overcurrent Protector). The confusion arises because manufacturers like Mitsubishi are now including “recommended breaker” sizes on data tags that are lower than the MCA—a courtesy to contractors, not a code requirement. The higher MCA reflects conservative safety margins that account for extreme operating conditions, but in practice, inverter-driven systems have multiple built-in protections that prevent them from ever actually reaching these calculated amperage levels. The key takeaway is that contractors can safely install breakers at the recommended size without safety concerns, as long as the breaker’s lugs are rated to accept the wire size required by the MCA.

The episode also explores how inverter-driven equipment fundamentally differs from traditional PSC motors, particularly regarding locked rotor amps (now more accurately termed “inverter input”) and voltage drop considerations. Unlike conventional motors that simply run slower with reduced voltage, inverter-driven compressors and ECM motors compensate by drawing more current to maintain performance, creating a potential compounding effect with voltage drop that installers need to understand—even though voltage drop itself isn’t an enforceable NEC code requirement.

Topics Covered:

New UL 60335-2-40 Edition 3 standards and their impact on electrical calculations for HVAC equipment
The relationship between MCA (Minimum Circuit Ampacity) and MOCP (Maximum Overcurrent Protector) and why they can now seem contradictory
Recommended breaker sizes on modern data tags and why they may be lower than the MCA
Handling inspector conflicts and failed inspections related to breaker sizing
Differences between inverter-driven equipment and traditional PSC motors in electrical behavior
The transition from “locked rotor amps” to “inverter input” terminology for modern equipment
Voltage drop considerations with inverter-driven systems (NEC 210.19A and 215.2A)
Why inverter-driven equipment draws more current at lower voltages compared to traditional motors
Proper wire and breaker sizing for A2L refrigerant equipment (454B systems)
NEC Section 440 requirements specific to air conditioning and refrigeration equipment
Breaker lug ratings and ensuring they can accept the required wire size
Practical advice for communicating with inspectors and resolving code disputes

Read the tech tip on this topic HERE.

Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool.

Purchase your tickets or learn more about the 7th Annual HVACR Training Symposium at https://hvacrschool.com/symposium.

Subscribe to our podcast on your iPhone or Android.

Subscribe to our YouTube channel.

Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android.

Search Episodes

Sizing Breakers and Conductors (for HVAC) – Have Things Changed?

01/01/2026

Bryan Orr

Absorption Cooling – The Rise and Fall and Rise – Short #272

12/30/2025